Functional cellulose-derived epoxy cross-linked with BADGE resin to construct high-performance epoxy composites.

The development of equipped bio-based epoxy materials has been gaining much attention recently. Nevertheless, finding the balance between the structure and properties of materials remains a significant challenge. In this work, cellulose-based epoxy (PHPCEP) with "soft" and "hard" cooperative structures was designed and demonstrated to endow bisphenol A diglycidyl ether (BADGE) with excellent toughness, heat resistance, mechanical strength, glass transition temperature, thermal stability, and solvent resistance. When 5 wt% PHPCEP was incorporated into BADGE composites, the resulting materials exhibited the maximum flexural strength (121.9 MPa) and tensile strength (71.4 MPa), a high glass transition temperature (148.3 °C), and 10 wt% PHPCEP/BADGE demonstrated the highest impact strength (70.5 kJ/m2). These figures are 18.8 %, 16.1 %, 21.5 %, and 254.3 % higher than the corresponding values of neat BADGE. The results of dynamic mechanical properties and heat degradation of the cured specimens also suggest that PHPCEP/BADGE materials have superior stiffness and toughness than neat BADGE, which could be attributed to the strong interaction between PHPCEP and BADGE, delivering better thermal stability for the composites compared to the pristine resin. Considering the remarkable effect, this work provides an effective way of highly efficient utilization of abundant cellulose and a high-performance additive for composite materials.

Cellulose-based polypropoxy ether carboxylates as highly compatible, effective, and migration-resistant plasticizers for poly (lactic acid).

The utilization of cellulose for enhancing the strength, the PLA has received significant attention, however, poor interfacial compatibility of solid cellulose with PLA matrix still hinders their broader application. Herein, highly compatible cellulose-based polypropoxy ether carboxylates (CPPEC) were firstly manufactured via propoxylation of cellulose and following esterification with acetic acid, butyric acid, as well as oleic acid, respectively. Liquid CPPEC delivered excellent performances to PLA, especially, the values of elongation at break and low-temperature resistance of PLA blended with cellulose-based polypropoxy ether acetate (PLA/CPPEA) were respectively increased by 630.9 % and 146.3 % compared with those of neat PLA due to the synergistic effect of propyl and methyl groups in CPPEC with PLA matrix. Additionally, migration resistance of PLA/CPPEA increased 14.3 and 11.2 times, respectively, compared with those of PLA specimens blended with epoxidized soybean oil and dioctyl phthalate. All findings suggest that the CPPEC is suitable for large-scale application in the PLA industry.

Recyclable TPA-Modified MIL-88-Supported Ionic Pt as a Highly Efficient Catalyst for Alkene Hydrosilylation.

The hydrosilylation reaction driven by a homogeneous catalyst has been widely used in the industrial synthesis of functionalized silicone compounds. However, the homogeneous catalyst for hydrosilylation has the shortcomings of nonrecyclability, undesirable side reactions, and high cost. In this work, a highly efficient heterogeneous catalyst was prepared by loading Pt ions on MIL-88 modified with trimethoxy[3-(phenylamino)propyl]silane. In comparison with previous research studies, the resulting catalyst can exhibit high catalytic activity and excellent stability during the hydrosilylation reaction, which was attributed to the presence of a pyrrolic nitrogen structure between TPA-MIL-88 and the Pt ion. Besides them, 1.2%Pt/TPA-MIL-88 showed the highest catalytic activity and can be reused five times without significant deactivation. Importantly, 1.2%Pt/TPA-MIL-88 also achieved satisfactory results when it was used to catalyze the hydrosilylation reaction for other olefins, implying great potential for application in the silicone industry.

High-Branched Organosilicon Epoxy Resin with Low Viscosity, Excellent Toughness, Hydrophobicity, and Dielectric Property.

Rapidly developing technology places higher demands on materials, thus the simultaneous improvement of materials' multiple properties is a hot research topic. In this work, a high-branched silicone epoxy resin (QSiE) was synthesized and applied to the curing system of bisphenol A epoxy resin (DGEBA) for modification investigations. When 6 wt% QSiE was added to the system, the viscosity dropped by 51.8%. The mechanical property testing results indicated that QSiE could significantly enhance the material's toughness while preserving good rigidity. The impact strength was enhanced by 1.31 times when 6wt% of QSiE was introduced. Additionally, the silicon skeleton in QSiE has low surface energy and low polarizability, which could endow the material with good hydrophobic and dielectric properties. This work provided a new idea for the preparation of high-performance epoxy resin additives, and provided a broad prospect for cutting-edge applications of epoxy resins.

Recyclable, UV-shielding, and biodegradable chitosan-based cardanol glycidyl ether as excellent water and oil resistance as well as gas barrier coating for paper.

Developing a feasible and low-cost approach to fabricate recyclable, UV-shielding, biodegradable as well as water- and oil-resistant coating for paper substance is still a challenge. Herein, novel full-biobased chitosan-derived cardanol glycidyl ether (CS-xCGE, x = 1/8, 1/4, 1/2, and 1) coatings with different contents of cardanol glycidyl ether (CGE) were developed for paper substance via the ethoxylation of cardanol and sequent addition with chitosan in a one-pot process. Benefiting from the hydrophobicity and ultraviolet resistance of CGE, the resultant CS-CGE (x = 1) coated paper exhibited not only remarkable oil resistance (kit rating value of 11/12), but also water resistance (Cobb 60 value of 5.78 g/m2), UV shielding and excellent recyclability. Compared with the uncoated paper, the mechanical properties of CS-CGE coated paper including tensile strength, folding strength, and resistance of water vapor permeability were improved 25 %, 63 %, and 73.4 %, respectively, which could be ascribed to the flexible long-alkyl chain in the structure of CS-CGE and the continuous and homogeneous CS-CGE derived film covered in paper substance. Most importantly, CS-CGE film is biodegradable when it is only buried in soil. This study affords a feasible and sustainable strategy for large-scale fabrication of full-biobased, recyclable, UV-shielding, water and oil resistant, as well as biodegradable coating for green paper-derived packaging.

Study on the Synthesis of Castor Oil-Based Plasticizer and the Properties of Plasticized Nitrile Rubber.

A series of new environment-friendly plasticizers was synthesized from castor oil and used to plasticize nitrile rubber (NBR). The test results showed that tensile strength, elongation at break, and tear strength of NBR vulcanizates plasticized by castor oil-based plasticizers were found to be better than that of dioctyl phthalate (DOP). The aging test taken demonstrated that the castor oil-based plasticizers could improve the hot air and oil aging resistance of NBR vulcanizates. The thermal stability test illustrated that castor oil-based plasticizers enhanced the thermal stability of NBR vulcanizates, and the initial decomposition temperatures (T10%) were about 100 °C higher than that of DOP. In general, the studies manifested that EACO and EBCO can replace DOP to plasticize NBR and are used in fields that require high mechanical properties, aging resistance, and thermal stability. This study emphasizes the effects of sustainable, cost-effective, and high-efficiency plasticizers on NBR.

Role of the Oxethyl Unit in the Structure of Vegetable Oil-Based Plasticizer for PVC: An Efficient Strategy to Enhance Compatibility and Plasticization.

Developing vegetable oil-derived primary plasticizers for poly(vinyl chloride) (PVC) is still a challenge because of their insufficient compatibility. As described in this work, we report the synthesis of plasticizers through the esterification of polyethylene glycol methyl ether and dimer acid, in which dimer acid is renewable material prepared via a two-step reaction (1) the hydrolysis of fatty acids from soybean oil at 70 °C and (2) subsequent Diels-Alder reaction at 250 °C. The resulting plasticizers, dimer acid-derived polyethylene glycol methyl ether esters (DA-2n, 2n = 2, 4, 6 or 8 referring to the number of oxethyl units per molecule), were blended with PVC. It was found that the tensile properties, transparency, and thermal stability of plasticized PVC (PVC-DA-2n) increased significantly with an increase in the number of oxyethyl units. Fourier-transform infrared spectroscopy analysis revealed that its good compatibility can be attributed to the strong interaction between oxyethyl units and PVC. As the number of the oxyethyl units of plasticizer increased, the glass transition temperature (Tg) of the corresponding plasticized PVC samples decreased from 62.3 (PVC-DA-2) to 35.4 °C (PVC-DA-8). Owing to the excellent plasticization of DA-8, the performances of PVC-DA-8 were comparable or better than that of the PVC plasticized using commercial dioctyl terephthalate (DOTP). The simple but efficient method of this study provides a new avenue for the preparation of vegetable oil-based plasticizers for PVC.

Catalytic Conversion of Biomass-Derived 1,2-Propanediol to Propylene Oxide over Supported Solid-Base Catalysts.

A series of supported alkali metal salts were investigated as catalysts to produce propylene oxide (PO) from biomass-derived 1,2-propanediol via dehydrative epoxidation in a solid-gas reaction system. The effects of supports, cations, and anions in the alkali metal salts and calcination temperature were investigated by X-ray diffraction and CO2-temperature-programmed desorption. The results indicate the catalysts with relative mild basicity having higher yields of PO. The highest yield of PO is 58.2% from reactions at 400 °C at an atmospheric pressure over KNO3/SiO2. In addition, the catalyst could be reused after calcination in air at 550 °C.